Cardosi Customs
Repairs
Mods
DIY
NEW ARRIVALS
Popular Send-In Services
IMPORTANT: The shipping address is included in the order confirmation email after your order is placed!
Unlock the ability to run homebrew software on your NS1, no matter the console variant, such as:
- Console overclocking
- Mods for your favorite games
OLED NOTE:
For Switch OLED variants, the kamikaze method is used, this is done to tap into DAT0 and is more reliable than tapping into it using the DAT0 flex PCB that connects to the solder ball on the eMMC.
ADDITIONAL INFORMATION:
I only need the tablet, I do not need any controllers, cables, the dock, or games.
While in there, your Switch will have all of its thermal paste replaced, so it’ll be good for another 5 or so years before it needs to be replaced again.
Made-to-Order (MTO) Switch prices are based on what I can get a new in box Switch for at my local GameStop
SD Card prices are based on A2 variants sourced from my local Micro Center.
CUSTOM FIRMWARE NOTE: Currently (as of March 16th, 2026) there isn’t a version of Atmosphere compatible with your Switch if it’s on version 22.0.0. Keep this in mind if you decide to go through with this service. The latest firmware version I can mod is 21.2.0 or below. Once a new version of Atmosphere comes out (currently version 1.10.2), you want to update that first and then update your console’s firmware.
Need to check if there’s a new Atmosphere version? Check here
Download Atmosphere
IMPORTANT: It is safest to only run custom firmware while offline, whenever you go online with mods and custom firmware you do run the risk of having your console being banned. If your console gets banned, refunds are NOT accepted.
DISCLAIMER: We do not condone the act of piracy, this is strictly meant to enjoy free software published by the community. ROMs will not be included with this service, period.
IMPORTANT: The shipping address is included in the order confirmation email after your order is placed!
Electrically reduces snapback on the left analog stick virtually eliminating all misinputs when using the stick. Essential for competitive and casual play.
IMPORTANT: The shipping address is included in the order confirmation email after your order is placed!
SHIPPING METHOD
Shipping Instructions: You may send either the entire Virtual Boy unit over, or if you have the tools you may send just the ribbon cable(s) and board(s). The latter option will save money on shipping and overall price, but is not recommended if you do not have the tools to open your Virtual Boy and remove the parts!
EYEPIECE REPAIR
From the factory the eyepieces’ ribbon cables are connected to the LED board by glue. Over time this glue loses its bond with the board, resulting in glitchy displays, blank displays, and, in some cases, lines. This service can either repair pre-existing issues or be preventative maintenance for your Virtual Boy so it can live a long, healthy life. It is always recommended to get both done!
DISCLAIMER: You will be informed if it is not a ribbon cable issue but rather a board issue, in which case is not repairable. In a case like that it’s a replacement that is required, of which I do not have on hand. If this is the case you will be refunded your money minus return shipping.
CAPACITOR REPLACEMENT
Not usual a necessary procedure, in my experience, capacitors haven’t been an issue in any of the consoles I’ve worked on. It could be worth doing if you’re wanting to ensure longevity.
DC-DC CONVERTER REPLACEMENT
The DC-DC Converter (also known as a buck converter) steps the 9 volt input down to 5 volts for the console to use. Further testing is required, but it does run cooler than the original DC-DC Converter, so it could result in longer battery life when using them. It is not common for the original DC-DC Converter to go bad, but it can occur.
SERVO VIBRATION FIX
If your console powers on but experiencing a loud vibration noise that cuts in and out repeatedly, your console’s servo board needs to be repaired. A fairly uncommon issue, but I have successfully repaired over half of the units I’ve seen with this issue.
IMPORTANT: The shipping address is included in the order confirmation email after your order is placed!
Disc Drive not reading games and already tried multiple discs and cleaning the laser? No problem!
How to diagnose whether you just need your capacitors replaced or both the capacitors and laser.
Bad Capacitors
Disc still spins and laser still moves, but game is not read (tries for 5 - 10 seconds then fails)
Discs read the longer the GameCube has to warm up.
Bad Laser
Disc does not spin as the laser does not detect a disc inserted in the disc tray (fails almost instantly)
Guaranteed to fix your disc drive and keep it running for years to come!
NOTICE: If a laser replacement is ordered and one is deemed to not be needed, you will be refunded the amount for the laser ($20).
Background Photographed By: @Porky_Draws
IMPORTANT DATES
Tipped Off 17: Haunted in Atlanta, GA
10/31 - 11/1
VENDING
Riptide 2026 in
Sandusky, OH
9/11 - 9/13
VENDING
TORG 2026 in
Columbus, OH
11/14 - 11/15
VENDING
Supernova 2026 in
Baltimore, MD
8/6 - 8/9
VENDING
Background photographed by: @Browningtons_
The ultimate memory card to keep your saves nice and safe.
- OLED Screen
- 3D Printed Nylon Shell
- Two Navigation Buttons (cycle through your virtual memory cards)
- 32GB Micro SD Card
- Multi-Region Capabilities (Able to save NTSC-U, NTSC-J, and PAL region games all on the same virtual memory card)
Click here for more information about the Flipper MCE.
Disclaimer: This was not designed by me, only sourced, soldered, and assembled by me. All credit in terms of design, programming, and open sourcing goes to the Flipper MCE Team.